M5 screw for attaching points cover

2 required per distributor. Can be used in place of hex bolt Guzzi ref. 98082225

 More than 5 in stock

Domino left hand switchgear with lights on - park - off, high and low beam, pass, indicator and horn switches. Same style switch as ELA01738.

Already wired in to 9 pin block connector (you may need to alter the wiring on your bike to correspond to this block connector). Originally fitted as standard to early V11 Sport models. See the wiring diagram on our technical documents page for help installing this switchgear. See Greg Bender's website for a custom sub-loom that enables easy fitting of this part to models previously fitted with LEGO style swithgear

 This part is due back in stock soon, call 01484 841395 to reserve yours

 01738030 GU01738030 01 73 80 30
 0173 8030 0173.8030 01.73.80.30

Magnetic oil drain plug for engine sump or filler plug for drive box and gearbox

Can also be fitted to V7 Sport, 750S, 850 GT and other early big twins which originally had a plain drain plug. May be supplied in either black or silver finish.. See SSA12600 and ACA12600 for stainless or aluminium versions of this part

 This part is due back in stock soon, call 01484 841395 to reserve yours

 12003702 GU12003702 12 00 37 02
 1200 3702 1200.3702 12.00.37.02

Splined drive plate incorporating cush drive (rubbers not included)

See WHA14336 for cush drive rubbers

 This part is available by special order, request a quote

 14335203 GU14335203 14 33 52 03
 1433 5203 1433.5203 14.33.52.03

Driveplate retaining circlip

 This part is available by special order, request a quote

 14335303 GU14335303 14 33 53 03
 1433 5303 1433.5303 14.33.53.03

Long 10 spline driveshaft

 This part is available by special order, request a quote

 29326300 GU29326300 29 32 63 00
 2932 6300 2932.6300 29.32.63.00

10 spline connection sleeve to connect drive box to driveshaft

 1 in stock

12327700-z 12327700 GU12327700 12 32 77 00
 1232 7700 1232.7700 12.32.77.00

Black rubber strap for retaining CDI/ECU

This only fits the smaller of the two ECUs fitted to the Cali 1100

 This part is due back in stock soon, call 01484 841395 to reserve yours

 29728960 GU29728960 29 72 89 60
 2972 8960 2972.8960 29.72.89.60

Complete electronic ignition kit containing alternator mounted ignition pickup, fittings and amplifier unit. Works with standard 12 volt coils and can be used to replace points or Bosch electronic ignition on models with Bosch charging systems. The pickups for this kit are mounted on the alternator stator. Supplied with instructions in German with wiring diagrams.

2 year warranty on Sachse ignition kits

Eliminates vague timing due to worn distributors on big twins. Preloaded with nine ignition curves, two of which are designed for twin plugged bikes. Once fitted no further adjustment should be necessary. See this link for fitting instructions. We recommend fitting Dyna coils ELA14101 with this kit. If you wish to combine this kit with uprated charging system ELA00502 you will need to make or source longer studs (M5 x 67mm x 2) for pickup, and longer centre bolt (M8 x 58mm wasted). See ACA50001 for distributor blanking plate if required

 This part is due back in stock soon, call 01484 841395 to reserve yours

Complete electronic ignition kit containing alternator mounted ignition pickup, fittings and amplifier unit. Works with 12 volt 3 Ohm coils ELA14500 (big twins) and can be used to replace Digiplex on models with Ducati charging systems where the bike is converted to carburettors. This kit is just an ignition system, it will not control fuelling. The pickups for this kit are mounted on the alternator stator. Supplied with instructions in German with wiring diagrams.

2 year warranty on Sachse ignition kits

Once fitted no further adjustment should be necessary. Preloaded with nine ignition curves, two of which are designed for twin plugged bikes. See this link for fitting instructions. Some bikes may need at least one additional spacer to allow enough clearance for alternator cover to fit once pickup is fitted. Note that if you are replacing a Digiplex system you will also need to replace your 'square' coils with higher impedance 12 volt coils e.g. ELA14500

 This part is available by special order, request a quote